LINEVO Foshan Plant · 15,000+ m² · 50+ Patents · Since 2013
CATALOG ID VFFS-MULTIHEADFAMILY LINEVO T01CATEGORY Multihead Weigher VFFS Lines

LINEVO Multihead Combination Weigher & VFFS Bagging Line

Engineered as a single synchronized vertical roll-film bagging line, this LINEVO T01 configuration pairs an overhead multihead combination weigher with a continuous servo-sealed VFFS bagger to pack free-flowing and semi-sticky granules at 30–70 bags/min (W 60–240 × L 80–350 mm) within ±0.3–1.5 g.

Check Fit for Multihead Weigher VFFS Line Request Itemized Scope & Layout

What It Is Built For vs. When to Choose Another Configuration

Use this rapid application screen to confirm whether Multihead Weigher VFFS Line matches your container geometry, product flow behavior, and target throughput before freezing specifications.

RECOMMENDED APPLICATION FIT

Use It For

  • Roasted whole or diced nuts, trail mixes, dried fruits, snack food granules, and co-packed dry foods packed from flat rollstock film.
  • Pillow and gusseted retail bags from 60–240 mm (2.36–9.45 in) wide by 80–350 mm (3.15–13.78 in) long requiring lowest unit laminate cost.
  • High-mix contract packaging rooms needing food-grade SUS304 contact parts with smooth or dimpled anti-sticking feeder pans.
  • Synchronized turnkey cells integrating Z-bucket elevation, gantry platform, nitrogen flushing review, and downstream checkweighing.
BETTER SIBLING ARCHITECTURE

When to Choose Another Configuration

Technical Specifications & Operating Conditions

Every value below is grounded in LINEVO's factory catalog for vffs-multihead, paired with exact arithmetic imperial conversions where millimeter, gram, kilogram, or liter units apply.

ParameterMetric ValueImperial EquivalentOperating Condition & Engineering Note
Listed packing speed30–70 bags/min—Operating conditions: bag volume, target weight and material flow; verify with your product.
Listed bag length80–350 mm3.15–13.78 inBag-size range; the forming set must match your pack.
Listed bag width60–240 mm2.36–9.45 inBag-size range with customizable forming tooling.
Listed weighing accuracy±0.3–1.5 g±0.011–0.053 ozWeighing tolerance depends on product uniformity and blend ratio; validate it with representative samples.
Product-contact materialSUS304—Review the product-contact material specification for the selected units.
Realistic Shift OEE Rule: Listed catalog speeds depend on bag/box volume, target fill weight, material flowability, and film seal dwell time. In continuous production, plan net shift output at 0.70–0.85 OEE to account for film splices, carton reloads, and sanitation—and validate your exact SKU during Foshan sample trials.

What Is Included vs. What We Review Per Project

Clear scope boundaries prevent startup surprises between the base machine and project-specific dosing, tooling, and plant interfaces:

BASE CONFIGURATION

Included in Core Machine Scope

  • Vertical roll-film bag forming, pulling, and servo heat-sealing base machine (SUS304 product contact)
  • Overhead multihead combination weighing arrangement synchronized to bagger dump signal
  • Oil-resistant independent servo cross-sealing control loop and touchscreen PLC recipe interface
APPLICATION-ENGINEERED

Reviewed & Specified With Your Quotation

  • Forming collar and tube set matched to each exact finished bag width (60–240 mm) and style
  • Smooth vs. embossed dimpled SUS304 vibratory pans and chutes for sugary or oiled dried fruits
  • Z-bucket infeed elevator, mezzanine support platform, nitrogen gas-flushing lance, and downstream checkweigher/metal detector

Working Sequence & Shop-Floor Countermeasures

Step-by-Step Operating Cycle

  1. STEP 01Bulk nuts, dried fruits, or granules feed evenly into the Z-bucket incline elevator and discharge into the top dispersion cone.
  2. STEP 02Radial vibratory pans (smooth or dimpled SUS304) meter product into pool and weigh hoppers; the scale microprocessor selects the combination closest to target weight (±0.3–1.5 g).
  3. STEP 03Rollstock laminate unwinds over the forming collar into a vertical tube and receives a longitudinal back seal.
  4. STEP 04Upon weigher-ready handshake, the combination charge drops cleanly down the forming tube while servo cross-sealing jaws seal the top of the filled bag, form the bottom of the next bag, and sever the finished pack onto the takeaway conveyor.

Real Production Floor Failure Modes & LINEVO Countermeasures

Sugary dried fruits (raisins, cranberries) bridging on vibratory pans and delaying dump cycles

Countermeasure: Embossed dimpled SUS304 texture across vibratory pans, buckets, and discharge chutes reduces surface contact area so sticky pieces advance cleanly.

Roasted nut oils contaminating transverse seal jaws and causing micro-leaks

Countermeasure: Oil-resistant continuous servo sealing loop controls jaw clamping pressure and dwell temperature independently of line speed fluctuations.

Product-in-seal jams when trailing pieces fall late from the overhead weigher

Countermeasure: Closed-loop PLC dump-timing synchronization holds cross-jaw closure until the combination drop window clears the forming tube.

Forming collar wrinkling or fin-seal starvation during rollstock width changes

Countermeasure: Dedicated bag-format forming sets engineered to your exact 60–240 mm bag width and verified on client laminate reels during Foshan FAT.

Sanitation bottlenecks between allergen nut blends and trail-mix SKUs

Countermeasure: Heavy-duty sanitary SUS304 contact construction allows tool-free bucket removal and rapid wash/wipe changeover between runs.

Comparing Quotations? Check These 5 Things First

5-Point Buyer Quotation Audit

  1. Speed Test Conditions vs. Shift OEE: Confirm whether quoted bags/boxes per minute reflect dry-cycle empty-film speed or filled product at your exact target weight, and plan net shift output using a realistic 0.70–0.85 OEE factor.
  2. Dosing & Upstream/Downstream Handshake: Verify mechanical chute/conveyor transitions and PLC ready/interlock signals between scales, primary sealers, cartoners, and checkweighers.
  3. Utility Power & Clean Dry Air Split: Match electrical panel build to your exact factory voltage, phase, and frequency (e.g., 220 V single-phase vs. 380 V/480 V 3-phase, 50/60 Hz) and confirm regulated oil-free dry air MPa and m³/min.
  4. Format Tooling for Extra Pack Sizes: Identify which pack dimensions adjust via HMI/handwheels versus which require dedicated forming collars, rotary discs, sealing chucks, or carton molds.
  5. Pre-Shipment Sample & Film FAT Run: Ensure the contract specifies a Foshan Factory Acceptance Test running your physical product samples and printed laminate reels or cartons before balance shipment.

Pre-Dispatch Foshan FAT & Project Sequence

STAGE 01Sample Audit

Bench check of your product flow, piece geometry, and film/carton tolerances in Foshan.

STAGE 02Written Scope Freeze

Signed station list, utility schedule, format tooling table, and 2D CAD floor layout.

STAGE 03Foshan Build

In-house CNC machining, SUS304/316L fabrication, and PLC electrical assembly.

STAGE 04Foshan FAT Run

Live or multi-angle video acceptance run on your actual packaging material before crating.

STAGE 05Crating & Startup

Sea-worthy export cases, bilingual HMI recipes, spare wear kit, and remote/on-site commissioning.

CONTROL CABINET & PNEUMATIC ARCHITECTURE · VERIFIED BOM

Control Cabinet & Pneumatic Hardware BOM

DIN-RAIL & MANIFOLD STANDARD
CAB-PLC · 01
SiemensPLC Motion & Sequence Controller

Main programmable logic controller coordinating dosing, film/pouch indexing, and sealing interlocks.

CAB-ENC · 02
OMRONRotary Encoder, Control Relays & 24V Switching Power Supply

Phase-angle timing feedback, cabinet switching relays, and regulated 24V DC power supply.

CAB-DRV · 03
Delta ElectronicsHMI Color Touchscreen & Variable Frequency Drive (VFD)

Multi-recipe color operator terminal and inverter motor speed control for main drives and conveyors.

CAB-PNU · 04
AirTACPneumatic Cylinders, Solenoid Valves, Vacuum Gauge & FRL Unit

Actuation cylinders, pneumatic manifold valves, vacuum manometer, and air preparation unit.

Representative electrical, sensing, and pneumatic hardware fitted on LINEVO packaging configurations; exact part series or project-specified alternatives are itemized in your written quotation BOM.

Frequently Asked Questions

What real shift output should we plan on a 30–70 bags/min LINEVO VFFS multihead line?

Catalog speed of 30–70 bags/min depends on bag length (80–350 mm), target weight, and product settling speed. At a realistic 0.75–0.85 shift OEE accounting for film reel splices and allergen wipe-downs, plants typically budget 42–56 bags/min sustained average (20,000–26,800 bags per 8-hour shift).

Can one VFFS forming collar run multiple bag widths inside the 60–240 mm window?

Bag length (80–350 mm) adjusts electronically from the HMI touchscreen via eye-mark or encoder pitch, whereas each distinct bag width requires its own matched forming collar and tube assembly.

When do we specify dimpled SUS304 plates instead of smooth stainless pans?

Smooth SUS304 pans suit dry roasted almonds, cashews, coffee beans, and crisp snacks. Dimpled embossed SUS304 pans are specified whenever syrupy dried fruits, glazed nuts, or oiled inclusions cling to flat metal.

What ceiling height is required when adding a Z-bucket elevator and gantry platform?

While the standalone VFFS bagger sits at floor level, stacking a multihead weigher on a walk-on SUS304/painted gantry platform fed by a Z-bucket elevator typically requires 3.8–4.5 m clear overhead height; confirm against the quotation layout drawing.

LINEVO FOSHAN TURNKEY DESK

Verify Multihead Weigher VFFS Line on Your Actual Samples

Message our Foshan engineering team with your pack dimensions, target fill weight, and shift output goal—no registration forms required.